Super Scrape Rubber Logo Mats put your logo on a mat that earns its place at the door. The nitrile rubber surface uses raised circular cleats to scrape dirt and water off shoes before they reach your floors, and the artwork is set into the rubber rather than coated on top — so the branding holds up through heavy traffic instead of scuffing away. They're among the most rugged of our outdoor logo mats, built for real commercial use indoors or out.

The logo is digitally printed on a polymeric film, then heat-pressed into the nitrile rubber so it becomes part of the mat. That process reproduces photo-realistic detail — multi-color artwork, tones, and gradients all come through cleanly, which is what separates these printed floor mats from simple one-color welcome mats. You get 150 standard colors to work from, with PMS matching available — up to four PMS colors per design — when a logo has to be exact.

The raised cleats give the mat a high-traction surface that's certified by the National Floor Safety Institute, which matters at a wet entrance where a slip turns into a liability claim. The all-nitrile build also resists oils and chemicals, so the mat holds up at tougher doorways — entries near commercial kitchens, service bays, and manufacturing floors — not just clean lobby entrances. It works indoors or out, though under constant direct sun the printed color softens over time.

The mat comes in standard sizes from 2.5' x 3' up to 6' x 8', so most entrances are covered without custom cutting — what's custom is the artwork, built to your logo and colors. Cleaning is simple: shake or sweep off loose debris and hose it down, or have it commercially laundered. Plan to replace it when the cleats wear smooth or the printed color has faded enough to lose its punch at the door.

Frequently Asked Questions

How well does the logo hold up outdoors and under heavy traffic?

Answered by Dustin Thompson, Owner & CEO

Better than a surface-printed mat. The artwork is printed on a film and heat-pressed into the nitrile rubber, so it's set into the mat instead of sitting on top as a coating that can scuff or peel. Under heavy door traffic, the raised cleats usually wear smooth before the logo gives out. Outdoors, direct sun is the limiting factor — the color softens gradually over the years rather than failing all at once.

Can you match our exact brand colors?

Answered by Jinna Hopson, Vice President of Marketing

Yes. There are 150 standard colors to work from, which covers most logos as they are. When a brand needs precise color, PMS matching is available for up to four colors per design. Because the image is digitally printed before it's pressed into the rubber, photo-realistic detail holds up — multi-color marks, gradients, and fine type come through cleanly instead of being simplified into flat blocks.

What artwork do you need from us, and how detailed can the logo get?

Answered by Jinna Hopson, Vice President of Marketing

Print-ready artwork works best — vector files or high-resolution images reproduce most cleanly. The process handles real detail, including photo-realistic images, multi-color designs, and shaded tones. As a rule of thumb, keep text at least half an inch tall and lines at least a sixteenth of an inch thick so they hold up in production. Send us the logo and the size you need, and we'll confirm how it reproduces before anything is made.

Can these go near kitchens or areas with oil and chemicals?

Answered by Dustin Thompson, Owner & CEO

Yes — that's one of the real advantages of nitrile rubber. Standard rubber softens and breaks down with regular oil and chemical exposure, while nitrile resists both. That lets the mat hold up at doorways near commercial kitchens, auto and service bays, manufacturing floors, and food-service areas, where a standard logo mat would degrade.

By Dustin Thompson, Owner & CEO, Mats Inc.

↑

What Dri-Dek does before standing water turns a floor slick and moldy

In a shower, sauna, locker room, or pool deck, water doesn't just make the floor slick — it sits. A flat surface, even a textured one, holds a film of water right where bare feet land, and the warm, damp film that lingers between uses is exactly what mold, mildew, and germs feed on. Mopping buys you a few minutes; the water comes back.

Dri-Dek solves it from a different angle: it lifts you above the water. Each tile is a raised, knobby, perforated grid, so water drains straight through and flows away underneath while you stand on the dry high points on top. Air circulates in the gap below, so the floor actually dries between uses instead of staying wet. You get grip up top and a floor that isn't a permanent puddle.

That combination matters in barefoot wet areas. Hygiene and cleaning authorities like ISSA stress that standing water and damp, hard-to-dry floors are what drive both slip risk and microbial growth in showers and locker rooms. A surface that keeps feet up out of the water and lets the floor beneath dry is tackling the slip and the mold problem at the same time.

Why an interlocking raised-vinyl build, and why this one

Dri-Dek is molded from a tough, UV-stabilized virgin vinyl in a flame- and chemical-resistant formulation, which is what lets it live on a wet floor for years. It resists the inorganic acids, oils, grease, detergents, and brine that wet areas and cleaning routines throw at it, holds up from -30°F to 167°F, and carries UV stabilizers so outdoor sun doesn't break it down. The same material is made to resist mold, mildew, and bacteria rather than harbor them.

The design is the other half. Each 12-by-12-inch tile is 9/16 inch thick with a knobby, perforated top, so it drains in every direction and cushions underfoot at the same time — the flex in the raised knobs takes some of the ache out of standing on hard concrete or tile. It's also flame resistant, having passed the UL 94V-0 vertical flame test, and it's tough, with a tensile strength around 2,750 PSI.

Best of all, it goes down without a contractor. The tiles, sheets, and rolls snap together on all four sides to build a surface of any size or shape, and they trim with a knife to fit wall-to-wall or around a drain, a bench, or a corner. Beveled edge and corner pieces finish the exposed borders into gentle ramps. When it's time to clean, you hose it, pressure-wash it, or lift a section and rinse under it.

Where it belongs — and what it isn't

Dri-Dek is at home anywhere a floor gets wet and stays wet. That's pool decks and pool surrounds, showers, saunas, steam and changing rooms, locker rooms, and the damp ring around a spa or hot tub. Because it interlocks into any shape and handles sun and temperature swings, it works indoors and out, in commercial facilities and in a home bathroom, basement, or patio alike.

It helps to be clear about what this isn't. It's a walk-on modular floor surface, not a flotation device, and not the liner sheet that goes under an above-ground pool. If you want a mat to put under a pool or a float for the water, this isn't that product. Dri-Dek installs on top of your existing floor — concrete, tile, or decking — and turns it into a dry, draining surface.

One honest note on chemistry: the vinyl resists most acids, oils, and solvents, but a few aggressive industrial solvents are the exception, so for a specialized chemical environment it's worth checking the specifics with us. In a normal pool, shower, or locker-room setting, chlorine, cleaning products, and daily wear are well within what it's built to take.

Three Things to Check Before You Spec It

Dri-Dek is simple to order once you've settled three things.

First, choose your format. Loose 1-by-1-foot tiles are the most flexible for a small or intricate space and for lifting individually to clean. Pre-assembled 3-by-4-foot sheets or 3-by-12-foot rolls cover a big pool deck or locker room far faster, snapping to each other just like the tiles. Many jobs mix them: rolls for the open floor, loose tiles to fill the edges.

Second, plan your edges. Wherever the surface meets open floor that people step onto, the beveled edge strips and corner pieces turn the 9/16-inch height into a gentle ramp, so there's no lip to trip on and carts or wheelchairs can roll on. Decide which sides are exposed before you order so you have the right trim on hand.

Third, pick a color with the room in mind. It comes in twelve colors, so you can go practical or design-led. Pool Blue and Blue lean fresh and aquatic on a deck; gray, black, and almond read neutral and hide grit in a locker room; brighter colors can zone an area or match a brand. Darker, muted tones show debris the least between cleanings.

Why Mats Inc.

We've been matching mats to real floors since 1964, and a wet floor is one place where the right surface pays off every single day. We'll help you work out how many tiles, sheets, or rolls your space needs, which edge and corner pieces to add, and which of the twelve colors suits the room — and we'll flag anything about your setting that matters before you order. It's part of our wider lineup of pool and wet-area matting, and every order is backed by our 1-year limited warranty.

Frequently Asked Questions

How does Dri-Dek keep you out of the water, exactly?

Answered by Dustin Thompson, Owner & CEO

It works by lifting you above the floor instead of just draining the top. Each tile is a raised grid of knobs with a perforated, open surface, so water falls straight through and flows away underneath while your feet rest on the dry high points. The gap beneath lets air move and the floor dry between uses, which is what stops the standing water and the mold and mildew that come with it. It's molded from a tough, UV-stabilized vinyl in a flame- and chemical-resistant formulation built to live in that wet environment.

Will it hold up to chlorine, sun, and years of wet use?

Answered by Dustin Thompson, Owner & CEO

It's built for exactly that. The vinyl resists inorganic acids, oils, grease, detergents, and the brine and chlorine of a pool environment, and it's UV-stabilized so sun doesn't make it brittle — in weatherometer testing it held around 98 to 99 percent of its tensile strength and color. It works continuously from -30°F to 167°F, so an outdoor deck through summer and winter is no problem, and it passed the UL 94V-0 vertical flame test. A couple of aggressive industrial solvents are the exception, so for a specialized chemical setting, check with us first.

How do the tiles, sheets, and rolls differ, and which should I get?

Answered by Dustin Thompson, Owner & CEO

They're the same surface in three formats, and they all interlock with each other. Loose 1-by-1-foot tiles are the most flexible — best for small or intricate spaces and for lifting one at a time to clean under. The 3-by-4-foot sheets and 3-by-12-foot rolls are pre-assembled tiles that cover a big pool deck or locker room much faster. Most large jobs mix them: rolls or sheets for the open floor, loose tiles to fill in edges and odd corners.

Where does Dri-Dek work best?

Answered by Jinna Hopson, VP of Marketing

Anywhere a floor gets wet and stays wet, indoors or out. It's a natural on pool decks and surrounds, in showers, saunas, steam and changing rooms, and locker rooms, and around the damp base of a spa or hot tub. Because it snaps into any shape and handles sun and temperature swings, it's just as at home in a commercial aquatic center as in a home bathroom, basement, mudroom, or patio. If the floor gets wet, it has a place there.

What colors does it come in, and how should I choose?

Answered by Jinna Hopson, VP of Marketing

It comes in twelve colors, which is part of what makes it easy to fit a space rather than fight it. Pool Blue and Blue feel fresh and aquatic on a deck or around a spa; gray, black, and almond read neutral and professional in a locker room and hide grit well; and the brighter colors — red, yellow, teal, green — can zone an area or pick up a facility's branding. If you want the floor to disappear and stay looking clean between washes, the darker, muted tones show the least debris.

My space is an odd shape — can I make it fit, and even design a pattern?

Answered by Jinna Hopson, VP of Marketing

Yes, and that's one of the best things about it. Because every piece interlocks on all sides and trims with a knife, you can build a surface to any footprint — around a drain, a bench, a curved pool edge — and finish the exposed sides with beveled edge and corner pieces for a clean, ramped border. And since it comes in twelve colors, you can mix them to create borders, lanes, or a simple pattern, or match a brand color. Send us your layout and we'll help you plan the pieces and colors.

Written by Jinna Hopson, VP of Marketing, Mats Inc.

Berber Logo Mats put your logo at the door on a looped berber surface — a tight, low-profile weave with a subtle hobnail texture that reads as upscale rather than promotional. The logo is digitally printed in high definition, so the artwork stays crisp, and the same tight weave that holds the print also scrapes dirt and moisture off shoes before either reaches your floor.

What a Berber Logo Mat Does Before Your Brand Looks Tired at the Door

A logo mat is doing two jobs from the moment someone walks up: it shows your brand and it protects the floor. ISSA field data shows a building takes on up to 12 times more dirt during wet weather, and it takes six to eight steps to walk a sole dry. A mat that catches that grit keeps your entrance clean — and keeps the logo from sitting in a smear of tracked-in dirt.

The looped berber weave is tight enough to scrape and hold dirt and moisture, so the floor past the mat stays cleaner and the logo stays legible instead of muddy. That matters because a worn or grimy logo mat does the opposite of its job — it makes the brand look neglected at the exact spot where a visitor forms a first impression.

Why Berber Loop, and Why This One

The surface is needle-punched PET fiber, about 44 ounces per square yard, made with at least 80% recycled content reclaimed from plastic bottles. The loop-pile berber has a smooth, even face, which is what lets the logo print crisply — the artwork is built up in layers of color and matched to a standard palette of 56 colors, so edges and lettering stay sharp.

Berber's tight weave is the durable part. It stands up to heavy foot traffic without the surface breaking down, and the hobnail texture gives it an upscale look that plain printed mats miss. The fiber is naturally stain- and fade-resistant, so the logo holds its color through regular cleaning rather than washing out after a season.

Underneath is an SBR rubber backing that contains 20% recycled tire content and keeps the mat in place to cut slipping. You can spec a universal cleated backing for carpet or a smooth backing for hard floors, and the whole mat sits low — easy to clean by vacuuming or hosing off, and low enough not to catch a door swing.

Where It Belongs (and Where It Doesn't)

This is a branding mat for indoor and covered-outdoor entries — lobbies, front desks, storefronts, building entrances, and anywhere you want a company logo greeting people as they arrive. As premium carpet logo mats go, the berber loop is on the upscale end, and it works equally well as commercial rugs with logo inside reception areas and retail floors.

What it is not is a full-sun outdoor mat. The print fades in direct sunlight, so it belongs under a canopy, an overhang, a vestibule, or indoors — not exposed on an open sidewalk. It's also a branding mat that catches dirt and moisture, not an aggressive scraper for mud and gravel; keep the heaviest debris to a coarse outdoor mat and let the berber handle the finish and the logo.

Three Things to Check Before You Spec It

Three things decide whether a berber logo mat is the right call.

First, the light. The print fades in direct sun, so this mat is for covered or indoor spots only. If your entrance faces open sky for hours a day, a different construction will hold its color better — be honest about the exposure before you commit the logo to it.

Second, the artwork. Logos print best with text at least 1.5 inches tall and lines no thinner than a quarter inch, and very fine detail or pale backgrounds don't translate well — light colors also show dirt faster. Simple, bold artwork in darker or neutral tones reads cleanly and stays looking sharp.

Third, the floor and the size. Choose a cleated backing for carpet or a smooth one for hard floors, and size the mat to the traffic, not just the doorway — aim to cover the six-to-eight steps it takes to dry a sole. Standard sizes run up to 6'×12', with custom lengths to 20 feet.

Why Mats Inc.

Mats Inc. has specified commercial matting since 1964, so when you're putting your brand on the floor, you're working with people who know which logo construction survives your specific entrance — and which will fade or flatten in it. We help you set up the artwork inside the print limits, pick the backing for your floor, and size the run so the mat protects as well as it presents. For the rest of the range, start with our commercial entrance mats.

Frequently Asked Questions

How is the logo actually printed, and will it stay sharp?

Answered by Dustin Thompson, Owner & CEO

The logo is built up in layers of color on the smooth berber surface and matched to a standard palette of 56 colors. That layering is what gives the high-definition look — crisp edges and clean lettering — as long as the artwork respects the print limits: text at least 1.5 inches tall, lines no thinner than a quarter inch, and no fine tints or transparencies. Bold, simple artwork holds up best. The fiber is naturally stain- and fade-resistant, so the print stays sharp through regular cleaning rather than washing out.

How well does it hold up to heavy traffic?

Answered by Dustin Thompson, Owner & CEO

The tight berber weave is the durable part — it's built to take heavy foot traffic without the surface breaking down, and the hobnail loop holds its texture rather than crushing flat the way a softer pile would. A mat that mats down stops scraping and starts looking worn, so that crush resistance is what keeps both the logo and the floor protection working.

The one thing that shortens its life is sunlight: the print fades in direct sun, so a covered or indoor spot is essential. Used under cover and cleaned regularly — vacuumed, or hosed off and hung to dry — it holds its look for years.

Can I put it outside?

Answered by Dustin Thompson, Owner & CEO

Only under cover. Berber logo mats are made for indoor and covered-outdoor entries — under a canopy, in a vestibule, or inside a lobby. They're not built for full sun, because the print fades when it's exposed directly, and they're branding mats rather than coarse scrapers for mud and gravel. The best setup outdoors is a rugged scraper mat first to take the heavy debris, with the berber logo mat just inside or under the overhang where it stays clean, dry, and out of direct light.

What sizes can I get?

Answered by Jinna Hopson, Vice President of Marketing

Standard sizes run from 2'×3' up to 6'×12', and custom lengths are available in standard widths up to 20 feet — useful for a wide storefront entry or a long lobby walkway.

Size it to the traffic, not just the door opening. Aim to cover the six-to-eight steps it takes to dry a sole, so the mat protects the floor and shows the logo at full size rather than getting walked past in a stride or two.

What does it look like, and what colors are there?

Answered by Jinna Hopson, Vice President of Marketing

It has an upscale, low-profile look — the looped berber weave with a subtle hobnail texture reads as refined rather than promotional, which suits a polished lobby or reception area. There are 56 standard colors to build the logo and background from, so you can match a brand palette closely. One tip: skip very light background colors, since pale tones show tracked-in dirt faster — darker or neutral backgrounds keep the mat looking clean longer between cleanings.

Can it match our exact brand colors, and what artwork works best?

Answered by Jinna Hopson, Vice President of Marketing

Colors are matched to a standard 56-color palette rather than exact PMS values, so it's a close brand match within that range rather than a precise ink match — worth knowing if your brand standard is strict. For artwork, bold logos and clear lettering reproduce beautifully; very fine detail, thin lines, gradients, and transparencies don't translate well to the woven surface. Send us your logo and we'll tell you straight whether it'll read well at mat scale or needs a small adjustment first.

By Jinna Hopson, Vice President of Marketing, Mats Inc.

Wonder Pro Matting is a plush, cut-pile olefin entrance mat made to soak up water and fine dust at the door, in a deep range of colors. Where some entrance mats scrape coarse grit, this one is built to wipe shoes clean and hold moisture and fine dirt — pulling it off the sole and keeping it on the mat, so a medium-traffic interior stays cleaner and drier past the threshold.

What Wonder Pro Matting Does Before Water and Dust Reach Your Floor

Most of what dirties an interior floor comes in on shoes — not just mud, but fine dust and moisture you don't always see. ISSA field data shows a building takes on up to 12 times more dirt during wet weather, and it takes six to eight steps to walk a sole dry. A mat at the door is where that gets caught before it spreads onto the floor.

Wonder Pro is built for the fine stuff. The plush cut-pile olefin face holds water and fine dirt rather than letting it pass through — it retains about 60% more liquid and fine dust than a standard mat — and a vinyl backing acts as a moisture barrier, keeping what the mat collects off the floor underneath instead of soaking through to it.

Why a Plush Olefin Surface, and Why This One

The face is cut-pile olefin — a dense, soft polypropylene pile that behaves like carpet and holds moisture deep in the fibers. That plush surface is what lets it pull moisture from shoes: a sole sinks slightly into the pile and leaves water and fine dust behind. The olefin resists fading, staining, mold, and mildew, so it keeps its look and doesn't turn musty as it works.

Underneath is a DINP-free PVC vinyl backing that doubles as a moisture barrier — it grips the floor and stops the water the mat holds from reaching the surface below. This mat holds moisture and fine dust rather than scraping coarse grit: it's rated for medium interior traffic and tuned for the fine stuff, not for knocking heavy mud off boots.

It also comes in a deep set of colors — Black, Castellan Red, Charcoal, Marlin Blue, Pebble Brown, and Walnut — so the mat can match a lobby or reception scheme rather than just sit there in standard gray. The colors are part of the point: this is the entrance mat for spots where the floor is on show.

Where It Belongs (and Where It Doesn't)

This is an interior, medium-traffic mat for spaces where appearance and a clean, dry floor both matter — office building lobbies, small retail floors, banks, churches, motels, and reception areas. It shines a few steps inside the door, finishing the job of drying shoes and catching the fine dust a coarse mat misses.

Where it's the wrong call is outdoors or against heavy mud and grit. As a plush mat it isn't built to scrape coarse debris or take the weather, and a flood of mud would clog the pile. The right setup is a scraper outside or at the first door, with Wonder Pro inside to finish the job — and to look good doing it.

Three Things to Check Before You Spec It

Three things decide whether Wonder Pro fits your entrance.

First, where it sits. Wonder Pro is a moisture-and-dust mat for the interior, after coarse debris is mostly off. If it's the only mat facing a muddy or gritty entrance, it'll load up faster than it can handle; paired with a scraper ahead of it, it does its job for years.

Second, the size. It comes in standard sizes from 2'×3' up to 6'×10', plus rolls and custom sizes up to 11'9" wide — useful for a wide lobby run or an odd opening. Size it to cover the steps it takes to dry a sole, not just the doorway.

Third, the color and the look. With six colors to choose from, pick a tone that fits the space and hides traffic — darker shades like Charcoal and Walnut stay looking clean longer between cleanings, while a color like Marlin Blue or Castellan Red can pick up a brand or interior accent.

Why Mats Inc.

Mats Inc. has specified commercial matting since 1964, so when the floor at your entrance is on display, we help you choose a mat that protects it and looks right doing it — matching the surface, size, and color to the space and the traffic. We'll also tell you when a spot needs a coarse scraper ahead of a plush mat like this rather than the plush mat alone. For the rest of the indoor range, see our all indoor entrance mats.

Frequently Asked Questions

How does a plush mat hold dirt and water?

Answered by Dustin Thompson, Owner & CEO

It's the opposite approach to a hard scraper. The face is a dense cut-pile olefin — a soft, carpet-like pile — and when a shoe presses into it, water and fine dust transfer off the sole and settle down between the fibers, where they stay instead of being tracked on. The pile holds about 60% more liquid and fine dirt than a standard mat. Underneath, a vinyl backing works as a moisture barrier, so the water the mat collects stays in the pile and off the floor below.

How much traffic can it handle, and what wears it out?

Answered by Dustin Thompson, Owner & CEO

It's rated for medium interior traffic — office lobbies, retail floors, reception areas, and similar spaces. In those spots it holds up for years, and the olefin resists fading, staining, mold, and mildew, so it keeps its look and doesn't turn musty as it absorbs moisture.

What wears it out early is the wrong job. A plush pile clogs and mats down if it's left to face heavy mud and grit alone, or placed where far more traffic crosses it than it's rated for. Keep it to medium interior traffic, with coarse debris handled ahead of it, and it lasts.

Can I use it outdoors, and how do I clean it?

Answered by Dustin Thompson, Owner & CEO

Keep it indoors. Wonder Pro is built for interior medium traffic — it isn't made for weather or for scraping heavy outdoor grit, so an exposed exterior door will wear it down fast. Inside, it's the mat that finishes drying shoes a few steps in. To clean it, vacuum regularly and extract or hose it off when it's heavily soiled, then let it dry fully before it goes back down — the olefin resists mold and mildew, but any mat works best dry.

What sizes can I get, and can it be made to fit?

Answered by Jinna Hopson, Vice President of Marketing

Standard sizes run from 2'×3' up to 6'×10', and it also comes in 60-foot rolls. If you need a custom size, it can be made up to 11'9" wide and 60 feet long — wide enough for a full lobby run or an unusual opening.

Size it to the traffic path, not just the door, so it covers the steps it takes to dry a sole. And if the mat will sit out in the open rather than wall-to-wall, ask for edged ends — standard rolls ship without edging unless you specify it.

What does it look like, and what colors are there?

Answered by Jinna Hopson, Vice President of Marketing

It has a plush, carpet-like surface that looks more finished and softer underfoot than a hard ribbed or rubber mat — a good fit for a lobby, bank, church, or reception area where the entrance is on display. There are six colors: Black, Castellan Red, Charcoal, Marlin Blue, Pebble Brown, and Walnut. The colors resist fading and staining, and darker tones like Charcoal and Walnut keep looking clean longer between cleanings, while Castellan Red or Marlin Blue can pick up a brand or interior accent.

Can I match it to our space or get a custom size?

Answered by Jinna Hopson, Vice President of Marketing

On size, yes — custom dimensions up to 11'9" by 60 feet mean you can fit a wide entry or a specific footprint rather than settling for the nearest stock size. On color, the six-color range lets you tie the mat to an interior scheme or a brand palette.

If you want an actual printed logo at the door, that's a different construction — a logo mat — and we can point you to one. Wonder Pro itself is about a clean, colored, plush surface that protects the floor and looks the part, rather than carrying artwork.

By Jinna Hopson, Vice President of Marketing, Mats Inc.

Cross-Over Matting is a loop-pile entrance mat that scrapes debris and moisture off shoes at the door while starting to dry them — the middle step in a layered entrance setup, between the coarse mat outside and the absorbent mat inside. The looped olefin surface is abrasive enough to clean shoes and resilient enough to hold its look in steady commercial traffic.

What Cross-Over Matting Does Before Dirt and Water Reach Your Floor

Dirt and water come into a building on shoes — and one mat at the threshold usually can't catch all of it. ISSA field data shows a building takes on up to 12 times more dirt during wet weather, and it takes six to eight steps to walk a sole dry. The most effective entrances use more than one mat to catch debris in stages.

Cross-Over is built to be the middle of that sequence. Its abrasive loop-pile surface scrapes off the grit and moisture a coarse outdoor mat leaves behind, and the sturdy olefin fibers begin drying the shoe before someone steps onto the floor or onto a softer absorbent mat further in. It's non-absorbent by design — it cleans the shoe and passes it along rather than soaking up and holding water.

Why a Loop-Pile Olefin Surface, and Why This One

The surface is a loop pile built from polypropylene ribbon yarn and continuous filament yarn — a combination that gives it an abrasive, hard-wearing texture rather than a soft plush one. That loop scrapes debris off the bottom of shoes and resists crushing, so it keeps its cleaning bite and its appearance instead of matting down into flat lanes under traffic.

The olefin fiber resists fading and crushing, which is what lets a loop-pile mat keep a tidy, finished look at a visible entrance over time. The loop construction reads richer than a flat ribbed mat, so it suits a lobby or front-of-house spot where appearance counts — while still doing real scraping work.

Underneath is a DINP-free PVC vinyl backing that grips the floor and protects it from whatever the mat scrapes off. It holds the mat flat on hard floors and low carpet, and at 5/16 inch the whole mat stays low enough not to catch a door swing or trip a foot at the edge.

Where It Belongs (and Where It Doesn't)

Cross-Over fits interior, medium-traffic entrances — convenience stores, restaurants, hotels, theaters, museums, and convention centers, where a steady stream of people crosses the threshold and the entrance is on view. It's certified high-traction by the National Floor Safety Institute, so it gives a safe surface where shoes arrive wet.

Where it falls short is as a building's only mat or as an outdoor scraper. It's the middle of a system, not the whole system: against heavy mud it wants a coarse scraper ahead of it, and because it's non-absorbent, a wet climate benefits from an absorbent mat inside it to finish the drying. Outdoors and in full weather, it isn't the right construction.

Three Things to Check Before You Spec It

Three things decide whether Cross-Over fits your entrance.

First, the rest of your matting. Cross-Over works best as the middle mat — a coarse scraper outside, this loop-pile mat at the door, and an absorbent mat inside. If it's going in alone, be honest about how much dirt and water it'll face, because one mat rarely catches it all.

Second, the size. Standard sizes run from 2'×3' up to 6'×10', and larger sizes over 6 feet — up to 11'9" — are made by seaming. Plan for that seam on the widest runs, and size the mat to cover the steps it takes to dry a sole, not just the doorway.

Third, the floor and the finish. The vinyl backing suits hard floors and low carpet and protects the surface beneath. If the mat will sit out in the open rather than wall-to-wall, order edged ends — standard rolls ship without edging unless you ask for it.

Why Mats Inc.

Mats Inc. has specified commercial entrance matting since 1964, so we don't just sell you a mat — we help you build the entrance. For a real front door we'll map the whole sequence, from the coarse scraper outside to the loop-pile mat at the threshold to the absorbent mat inside, and tell you where Cross-Over fits in yours. We match construction to traffic and size to the doorway. For the rest of the indoor range, see our all indoor entrance mats.

Frequently Asked Questions

How does a loop-pile mat clean shoes?

Answered by Dustin Thompson, Owner & CEO

The surface is a loop pile made from polypropylene ribbon and filament yarn — a tough, slightly abrasive texture rather than a soft plush one. As a shoe crosses it, the loops scrape grit and surface moisture off the sole, and the olefin fibers start drying the shoe. It's non-absorbent on purpose: instead of soaking up and holding water like a plush mat, it cleans the shoe and passes it along, which is why it works best as one mat in a layered entrance rather than the only one.

Will it crush down or fade in a busy entrance?

Answered by Dustin Thompson, Owner & CEO

It's built to resist both. The loop-pile construction is crush-resistant, so it holds its texture instead of matting flat into shiny traffic lanes, and the olefin fiber resists fading, so the color stays even at a visible entrance. Those two things are what usually go first on a loop mat, and they're the ones this construction is made to hold.

It's rated for medium interior traffic — convenience stores, restaurants, hotels, and similar spots. Pushed past that, or left to face heavy mud alone, any loop mat loads up and wears faster, so the way to get years out of it is to keep it to medium traffic with coarser debris handled ahead of it.

Can I use it by itself, or outdoors?

Answered by Dustin Thompson, Owner & CEO

It's designed as the middle mat in a layered entrance, not a standalone or an outdoor mat. The best setup is a coarse scraper outside to take heavy debris, Cross-Over at the threshold to scrape off what's left and start drying, and an absorbent mat just inside to finish — because Cross-Over is non-absorbent, it doesn't hold much water on its own. Used alone at a busy or wet door, more gets past it than you'd want; outdoors, it isn't built for the weather.

What sizes can I get?

Answered by Jinna Hopson, Vice President of Marketing

Standard sizes run from 2'×3' up to 6'×10', and it comes in 60-foot rolls. Larger mats over 6 feet — up to 11'9" — are made by seaming panels together, so a wide lobby run is possible, just with a seam in it.

Size the mat to the traffic path, not only the door, so it covers the steps it takes to dry a sole. If it'll sit out in the open rather than wall-to-wall, ask for edged ends — standard rolls ship without edging unless you specify it.

What does it look like, and what colors are there?

Answered by Jinna Hopson, Vice President of Marketing

The loop-pile surface has a richer, more textured look than a flat ribbed or rubber mat, which is why it suits a front-of-house entrance — a hotel lobby, a restaurant, a museum — where the floor is on display. It comes in two two-tone colors, Brown and Gray, both designed to blend with common interior schemes and hide tracked-in dirt between cleanings. The two-tone effect helps the mat read as finished rather than utilitarian while it does its work.

Can I get it in a custom size or with our logo?

Answered by Jinna Hopson, Vice President of Marketing

On size, yes within limits — beyond the standard sizes, widths over 6 feet up to 11'9" are made by seaming, so you can cover a wider entrance with a seam in the mat. On a logo, no: Cross-Over is a plain two-color loop mat, not a printed or logo construction. If you want branding at the door, that's a different product — a logo mat — and we can point you to one. For a clean, hard-wearing mat that looks the part at a front entrance, Cross-Over does that without the artwork.

By Dustin Thompson, Owner & CEO, Mats Inc.

Safety Step rubber mats take a different approach to wet-area matting: instead of one big mat, you build the footprint you need from 3-by-3-foot modular sections with molded-in connectors on two sides. Perforations drain water and oil through the surface, cushioned rubber eases long standing shifts, and when one section finally wears out, you replace that section — not the whole installation.

What Safety Step Does Before a Layout Outgrows Its Matting

Most wet-area mats are cut to a rectangle and stay that way. Work areas aren't. Lines wrap around equipment, stations get added, a sanding cell moves across the shop — and a fixed mat that fit last year now leaves gaps where feet land on bare, wet floor.

A modular anti-fatigue mat solves that at the design level. Sections connect into whatever shape the work takes, wrap odd corners, and re-assemble when the layout changes. Underneath, a multi-nib backing lifts the whole surface off the floor so drained liquid keeps moving and the floor beneath can actually dry, instead of holding a wet film under the rubber.

Why This Construction, and Why This One

The mat comes in two compounds, and choosing between them is most of the spec decision. The black version is general-purpose rubber for wet duty — water, washdowns, standard cleaners — with recycled content up to 47%. The terra cotta version is a nitrile rubber blend built to resist grease, for kitchens and stations where oil reaches the floor daily.

Both wear hard: surface loss measures at or under 1% after 1,000 abrasion cycles on the standard test. And both share the modular system's quiet economics — a high-wear section at the sink or the grinder swaps out individually, while the rest of the installation stays in service.

Edging is optional rather than built in. Snap-on beveled ramps finish exposed sides where traffic steps on and off; sides butted against equipment or walls can stay square. Adding edging extends the mat roughly 3 inches per finished side, which matters when you're sizing to a tight footprint.

Where It Belongs, and What It Is Not

Safety Step earns its place in factories, workstations, sanding and grinding cells, dish rooms, and food service areas — heavy-duty wet and oily zones, and especially the large or odd-shaped ones a single rectangular mat can't cover cleanly. If the matting footprint might change in the next few years, modular is the format that keeps up.

It is not a dry-station comfort mat — a salon chair or standing desk wants a solid surface, not perforations. And for one fixed, standard-sized station that will never move, a single one-piece mat from the anti-fatigue mats and runners range does the job without assembly. This mat's case is coverage that's big, irregular, or likely to change.

Three Things to Check Before You Spec It

First, what reaches the floor. Water and cleaning solution point to the black general-purpose version. Grease, fryer oil, or petroleum-based fluids point to the terra cotta nitrile blend — putting the general-purpose compound under daily grease shortens its life and turns the surface slick sooner.

Second, the true footprint. Sections are 3-by-3, custom assemblies run up to 12 by 30 feet, and workstation layouts order in full-foot increments. Sketch the actual standing and walking zone around the equipment — the point of modular is covering that real shape, not the rectangle that approximates it.

Third, the exposed edges. Count the sides where people step on and off, and spec snap-on ramps for those; remember each finished side adds about 3 inches to the overall dimension. An unramped edge in a walk path is a stubbed toe waiting for a rush.

Why Mats Inc.

Modular matting gets ordered wrong in predictable ways — the compound that doesn't match the fluids, the layout that forgot the edging inches, the section count that's one short. Send us a sketch of the work area with what lands on the floor, and we'll spec the sections, compound, and ramps so the kit that arrives assembles into the mat you actually needed.

Frequently Asked Questions

What's the difference between the black and terra cotta versions?

Answered by Dustin Thompson, Owner & CEO

The compound. Black is general-purpose rubber — right for wet zones where water and standard cleaners are the exposure, and it carries up to 47% recycled content. Terra cotta is a nitrile rubber blend formulated to resist grease and oil, which is what you want under a fry line, in a machine shop, or anywhere petroleum-based fluids hit the floor.

If you're unsure, name the messiest thing that reaches that floor in a normal week. Grease in the answer means terra cotta.

How long does a modular drainage mat like this last?

Answered by Dustin Thompson, Owner & CEO

The wear data is unusually strong: both compounds lose 1% or less of their surface after 1,000 cycles on the standard abrasion test, which puts heavy daily duty in the multi-year range — three to five years is a fair expectation with routine rinsing.

The modular format changes the replacement math, though. Wear never lands evenly — the section at the sink or the grinder goes first. Here you swap that one section and keep the rest in service, instead of retiring a whole mat because one corner died.

How do the sections install, and do they need adhesive?

Answered by Dustin Thompson, Owner & CEO

No adhesive. Each section has connectors molded into two adjoining sides, so you lay the first section at the primary work position and snap outward until the footprint is covered. Check every joint as you go — a proud seam collects debris and catches toes.

Start on a clean, dry floor, orient the assembly so drainage runs toward the floor drain, and snap ramps onto any edge that faces foot traffic. Reconfiguring later is the same process in reverse.

Will terra cotta look better than black in a kitchen guests can see into?

Answered by Jinna Hopson, VP of Marketing

Often, yes — and not just on looks. Terra cotta is the traditional working color of commercial kitchens, so in an open-kitchen or chef's-counter setting it reads as authentic professional equipment. It also happens to be the grease-resistant compound, so the aesthetic choice and the right technical choice usually point the same direction in food service.

Black suits back-of-house and industrial floors where it disappears against dark concrete. Whichever you pick, keep it consistent across connected sections — a checkerboard of mixed colors reads as patched.

What sizes can I build, and can it fit an odd-shaped area?

Answered by Jinna Hopson, VP of Marketing

Odd shapes are the point. Sections are 3-by-3 feet and connect in any direction, so an L around a prep island, a U inside a work cell, or a long dish-room run all assemble from the same units. Custom assemblies go up to 12 by 30 feet, ordered in full-foot increments.

Two sizing notes: optional edging adds about 3 inches per finished side, and it's worth ordering to the real standing zone rather than rounding down — a footprint that stops one section short leaves someone half off the cushion all shift.

Is this the right choice over a single one-piece drainage mat?

Answered by Jinna Hopson, VP of Marketing

It depends on the shape and the future. One fixed station with standard dimensions is happily served by a one-piece mat — nothing to assemble, nothing to seam. Choose modular when the area is large, wraps equipment, doesn't match stock rectangles, or is likely to be rearranged.

The section-replacement benefit tips close calls: if one spot in your layout takes far more punishment than the rest, modular means that spot never forces a full replacement.

By Dustin Thompson, Owner & CEO, Mats Inc.

What Heronair does before a wet work floor causes a fall

In a busy work area, the floor gets wet and stays wet — washdown, splashes, drips, tracked-in water. It's easy to assume a quick mop or a coat of non-slip paint keeps people safe. The catch is that water spreads into a thin film on a hard floor, right where people walk and stand, and a painted or tiled surface that grips dry can turn slick the moment it's wet.

Heronair is built to take that film out of play. It's an open-grid PVC mat that's impermeable to fluids, so water and debris drop through and disperse below the surface instead of pooling on top. The etched surface gives shoes traction, and the mat keeps draining even when the floor around it is soaked. That's the difference between a real non-slip wet-area mat and a surface that only behaves when it's dry.

A wet, slick work floor isn't a minor nuisance. The National Floor Safety Institute ties wet, hard floors to a large share of slip, trip, and fall injuries, and a walkway or wet work zone keeps feeding that risk shift after shift. A mat that drains the water away and holds grip underfoot is doing safety work the whole time it's down.

Why a lightweight tubular PVC build, and why this one

Heronair is made from non-porous PVC in a two-layer, tubular construction — and that hollow build is the heart of what makes it different. The tubes make the mat genuinely light: at around 0.9 pounds per square foot, it's easy to lift, roll, and reposition by hand. In a space where mats get pulled up for cleaning or moved between tasks, that lightness is a real day-to-day advantage.

The same open structure that keeps it light also keeps it draining. Liquids pass straight through and clear away beneath the mat, and it's certified slip resistant at R11 with V10 drainage under DIN 51130. Grip comes from an etched surface, so traction is strongest across the lines of the pattern. The hollow body also insulates against a cold floor and absorbs sound, taking some of the chill and clatter out of a hard work area.

Because people stand on these floors for hours, the cushioning matters. The give in the tubular build reduces fatigue underfoot, which is easier on legs and backs than bare concrete. The PVC itself resists most acids, alkalines, and oils, handles UV without degrading, and works from below freezing up to 140°F. Made in black, it's produced from post-industrial recycled material — averaging at least 30% recycled content — and the whole mat is 100% recyclable.

Where it belongs — and what it isn't

Heronair belongs in wet, working spaces where people are on their feet in shoes. Think light-industrial areas and walkways, washdown zones, beverage and prep stations, and the wet service and back-of-house areas around a pool — pump and equipment rooms, plant rooms, and staff walkways — rather than the barefoot deck itself. Wherever liquids underfoot meet standing workers, it earns its place.

It's worth being clear about what this mat is not. It's a shod, walk-on work mat — not a barefoot-certified pool mat, not a flotation device, and not the liner sheet that goes under an above-ground pool. For the barefoot pool deck, shower, or changing room, a barefoot-rated mat is the right call. Heronair's job is the working wet floor, in shoes, where drainage and anti-fatigue support matter most.

How it goes down is simple. It comes in 33-foot rolls, cuts to fit on site, and contours to uneven surfaces, so it follows a real floor instead of fighting it. For larger areas, rolls join side-to-side and end-to-end with connector clips or welded snap track, and ramped edging finishes an exposed border so the mat doesn't become a trip point.

Three Things to Check Before You Spec It

Heronair is easy to order well once you've thought through three things.

First, match it to the duty. This is the lighter, more versatile end of wet-area matting — ideal where you want easy handling, anti-fatigue support, and reliable drainage in shoes. For the most punishing wet floors or the highest wet-grip demands, a heavier, higher-traction mat may suit better. Be honest about how hard the floor gets worked before you choose.

Second, measure the whole wet path and plan the joins. Size the mat to cover wherever liquid actually reaches — the full washdown zone, the length of a walkway — since a dry-foot gap is where the next slip waits. For bigger areas, map where rolls will join with clips or snap track and where ramped edging finishes the border.

Third, plan for heat and movement. The PVC handles a wide temperature range, but like any thermoplastic it can shrink slightly — up to about 2%, faster in heat — so in a hot space or an exposed spot, leave a little room at fixed edges rather than butting it tight wall to wall, and use edging or clips to keep sections in place.

Why Mats Inc.

We've been matching mats to real floors since 1964, and wet work areas are where the wrong mat shows up fastest — in sore legs, slick steps, and mats too heavy to bother moving. We'll help you decide whether Heronair's lightweight, easy-handling build fits your space or whether a heavier mat suits the duty, size it to your actual wet path, and plan the seams and edging. It's part of our wider lineup of pool and wet-area matting, and every order is backed by our 1-year limited warranty.

Frequently Asked Questions

What's Heronair made of, and why is it so light?

Answered by Dustin Thompson, Owner & CEO

It's made from non-porous PVC in a two-layer, tubular construction — essentially an open grid of hollow tubes. That hollow build is why it's light: about 0.9 pounds per square foot, easy to lift, roll, and move by hand. The open structure also means it's impermeable to fluids — water and debris drop straight through and clear away underneath instead of pooling on top. So the same thing that makes it light also makes it drain, and keeps the walking surface usable when the floor's wet.

How slip-resistant and tough is it, especially with chemicals around?

Answered by Dustin Thompson, Owner & CEO

It's certified slip resistant at R11 with V10 drainage under DIN 51130, with traction coming from an etched surface — grip is strongest across the lines of the pattern, reading 58 to 77 wet on the ASTM E303 pendulum test depending on direction. On toughness, the PVC resists most acids, alkalines, and oils, stands up to UV without degrading, and works from below freezing up to 140°F. That's what lets the same mat hold up in a washdown area, a chemical-prone work zone, or an outdoor walkway without going brittle.

What sizes does it come in, and can it cover a large floor?

Answered by Dustin Thompson, Owner & CEO

It comes in 33-foot rolls in 2-, 3-, and 4-foot widths, and you cut it to fit on site. For a large floor, rolls join side-to-side and end-to-end with connector clips or welded snap track, so you can cover a whole walkway or work area in one continuous surface. Because it contours to uneven ground, it follows a real floor rather than needing a perfectly flat one, and custom matting is available when a standard width won't fit.

Can I use this around a pool, or is it really a workplace mat?

Answered by Jinna Hopson, VP of Marketing

It's really a workplace mat, and that's where it shines — light-industrial areas, walkways, washdown and prep zones. Around a pool, its place is the working, in-shoes areas: pump and plant rooms, staff walkways, and back-of-house service spaces, rather than the barefoot deck or shower. For those barefoot areas you'd want a barefoot-rated pool mat instead. If your space is a wet floor where people work on their feet in shoes, Heronair fits.

What does it look like underfoot?

Answered by Jinna Hopson, VP of Marketing

It has a practical, industrial look — an open, etched grid that clearly reads as a working surface built to drain and grip, not as decoration. The standard color is black, which is the easy choice for a work area because it hides the grit, oil, and debris these floors collect between cleanings; the black version is also the one made from recycled material. Other colors are available if you want to mark off a zone or match a scheme — tell us what you need and we'll confirm the options.

My work area has an awkward layout — will it fit, and is it easy to live with?

Answered by Jinna Hopson, VP of Marketing

Yes on both counts. Because it cuts to fit on site and contours to uneven surfaces, you can shape a run around machinery, drains, and corners instead of forcing the space to match a fixed mat. And it's genuinely easy to live with day to day: it's light enough to lift or roll up for cleaning by hand, needs no special tools, and rinses down with a hose. Send us your layout and we'll help you plan widths, joins, and edging.

Written by Dustin Thompson, Owner & CEO, Mats Inc.

Safe Walk mats are the straightforward heavy answer for wet and greasy standing zones: a one-piece rubber anti-fatigue mat, 7/8 of an inch thick, with circular drain-through holes and square-cut edges built to take years of abuse. Three versions cover the range — general-purpose black, black with pre-assembled yellow safety borders, and a grease-resistant terra cotta nitrile blend.

What Safe Walk Does Before the Edges Give Out

Drainage mats rarely die in the middle. They die at the edges — thin bevels that curl after months of cart wheels and boot toes, then crack, then turn the mat itself into the trip hazard it was bought to prevent. Meanwhile the wet floor problem never went away: liquid where feet plant, all shift.

This rubber standing mat attacks both ends of that story. The holes pass water, grease, and debris through the surface so footing stays sure, the resilient rubber body cushions long hours on concrete, and the robust square edges keep their shape where lighter perimeters fail first.

Why This Construction, and Why This One

The build is deliberately simple: heavy-duty rubber, 7/8 inch thick, one piece. That thickness keeps the cushion working under all-day industrial standing, and the compound carries up to 40% recycled material.

The version choice does the specifying. General-purpose black handles wet duty — washdowns, water, standard cleaners. The terra cotta version is a nitrile rubber blend for floors that see grease and oil daily. And where edge visibility matters in a fast-moving space, the bordered version arrives with yellow safety borders already assembled — no separate edging to order, fit, or lose.

Where It Belongs, and What It Is Not

Safe Walk earns its footprint in industrial workstations, food processing areas, commercial kitchens, bars, and cafeterias — the wet and oily floors where a mat gets hosed off as often as it gets stood on. If your station is a fixed rectangle that takes a beating, this one-piece format is the low-maintenance pick.

It is not a dry-area comfort mat; a solid surface serves salons, counters, and standing desks better than perforations ever will. And for sprawling or odd-shaped coverage that a rectangle can't fit, a modular system is the better tool. Within the full range of anti-fatigue floor mats, Safe Walk is the fixed-station heavyweight.

Three Things to Check Before You Spec It

First, the compound against the floor's reality. Water only: general-purpose black does the job. Grease, fryer oil, or petroleum fluids in the mix: go terra cotta nitrile — a general-purpose compound under daily grease softens and shortens its own life.

Second, whether the edge needs to announce itself. In a dim back-of-house or a fast line, the pre-assembled yellow-border version marks the mat's perimeter for people moving at speed. In a calm, well-lit station, plain black keeps a lower profile.

Third, the footprint against the size runs. The standard mat is 3 by 5 feet; the bordered versions come pre-assembled in set sizes up to 124 inches long, in three-sided and four-sided border layouts. Measure the real standing path — the border layout should match which sides face open floor.

Why Mats Inc.

The mats that come back for early replacement almost always failed the same way: right idea, wrong compound, or an edge that met a cart path it wasn't specced for. Tell us what runs across your floor — liquids, wheels, and feet — and we'll confirm which Safe Walk version and border layout holds up in that exact spot before you commit.

Frequently Asked Questions

Which Safe Walk version do I need — black, bordered, or terra cotta?

Answered by Dustin Thompson, Owner & CEO

Answer two questions. What's in the liquid: if grease or oil reaches that floor in a normal week, take the terra cotta nitrile blend; if it's water and cleaners, black is right. And who's moving past it: if staff cross that zone at speed or the light is poor, the yellow-bordered version makes the mat's edge unmistakable.

How long does a mat this heavy actually last?

Answered by Dustin Thompson, Owner & CEO

At 7/8 inch of heavy rubber, this is built for the long haul — years of daily washdown duty is the normal run, and the square-cut edges remove the usual first failure point, since there's no thin bevel to curl and crack.

What still ends one early: the wrong compound under constant grease, or drain holes left clogged until debris grinds the surface. Rinse it on schedule and check that edges still sit dead flat; when one won't, plan the replacement.

How should it be placed, and does it need anchoring?

Answered by Dustin Thompson, Owner & CEO

No anchoring — at this weight the mat holds its position. Set it on a clean, dry floor centered on where feet actually plant through the shift, and orient it so what drains through moves toward the floor drain rather than into the walk lane.

Lift it during floor cleaning so the concrete beneath dries fully, then set it back the same way each time.

Is the yellow border too industrial-looking for a bar or cafeteria guests can see?

Answered by Jinna Hopson, VP of Marketing

It depends what story the space tells. In a cafeteria or service line, a clean yellow border reads as a well-run operation that takes footing seriously — the same cue as a marked step. Behind a polished bar, plain black usually sits better, disappearing against the floor while the bartender gets the cushion.

The nice thing about a three-version lineup is you don't have to compromise: bordered where safety marking fits the room, plain where it doesn't.

What sizes are available, and what do "3-sided" and "4-sided" borders mean?

Answered by Jinna Hopson, VP of Marketing

The plain black and terra cotta versions come in the standard 3-by-5-foot mat. The bordered version arrives pre-assembled in sizes from 26-by-40 inches up to 124-inch lengths.

Three-sided means the yellow border wraps three edges, leaving one short edge square to butt flush against a counter, sink base, or wall. Four-sided wraps everything, for a mat that floats in open floor with traffic from any direction. Match the layout to which sides actually face walking space.

Would this suit a busy home kitchen, or is it commercial overkill?

Answered by Jinna Hopson, VP of Marketing

For most home kitchens it's more mat than the floor needs — nearly an inch of industrial rubber with drainage holes belongs where floors get hosed, not mopped weekly. A solid-surface cushioned kitchen mat gives home cooks the comfort without the perforations.

The exception is the home that runs commercial: canning weekends, a serious home bar, a prep-heavy kitchen with a wet zone. If you're regularly standing on a wet floor for hours, the commercial answer is the honest one.

By Dustin Thompson, Owner & CEO, Mats Inc.

Corrugated Rubber Matting

Corrugated Rubber Matting provides superior traction and floor protection in high-traffic and industrial environments. The ribbed, corrugated rubber runner surface offers enhanced slip resistance, making it ideal for wet or dry areas where safety is a priority. Its durable rubber construction ensures long-lasting performance, making it perfect for a wide range of applications, from warehouses to workshops.

Key Features of Corrugated Rubber Matting

• Slip-Resistant Surface: The corrugated rubber runner design improves grip, reducing the risk of slips and falls in both wet and dry conditions.
• Durable Construction: Made from high-quality rubber, this matting is designed to withstand heavy foot traffic and daily wear and tear.
• Floor Protection: Protects floors from damage caused by heavy equipment, tools, and other industrial activities.
• Easy to Install: Available in rolls, corrugated rubber matting is easy to cut and customize for various spaces and applications.
• Low Maintenance: Resistant to moisture and most chemicals, making it easy to clean and maintain for long-term use.
• Versatile Applications: Ideal for industrial settings, garages, warehouses, and workstations where safety and durability are essential.

Perfect for Industrial and Commercial Use

Corrugated Rubber Mats are the perfect solution for creating a safe and durable surface in industrial and commercial environments. Its slip-resistant and heavy-duty design makes it ideal for protecting both workers and floors in high-traffic areas.

Corrugated rubber matting is a durable, slip-resistant flooring material designed for high-traffic areas and industrial environments. Its corrugated surface provides enhanced traction, reducing the risk of slips and falls. This type of corrugated rubber matting is often used for floor protection and to improve safety in workplaces, entryways, and other areas prone to moisture or heavy use.

Super Berber Matting is a dense berber entrance mat that does the two hardest jobs at a busy door at once: it scrapes grit off shoes and soaks up the moisture they carry. The needle-punch berber surface is solution-dyed in up to 40 colors, and a custom logo can be inlaid right into it — so it cleans the entrance and carries the brand in the same mat.

What Super Berber Does Before Dirt and Water Reach the Floor

At a busy entrance, dirt and water arrive on shoes — ISSA research shows the door is where most of a building's dirt comes in. Left to cross the threshold, that grit grinds at the floor and wet shoes leave a lobby slick. The dense berber pile catches both: it scrapes solids loose and holds moisture in the fiber, while the all-weather rubber backing keeps the mat planted, so the dirt and water stay on the mat, not the floor.

Why Solution-Dyed Berber, and Why This One

The mat is built from 100% solution-dyed polypropylene berber, needle-punched into a dense half-inch pile that weighs about 52 ounces per square yard. Solution-dyed means the color is locked into the fiber rather than printed on top, so it does not bleach or wear pale. The polypropylene is UV- and abrasion-resistant, which is what lets the mat hold its look under heavy traffic and sun.

Of the two jobs an entrance mat does, this one leans toward wiping — the deep pile is built to pull moisture and fine dirt off shoes and keep it there, with strong scraping behind it. An all-weather rubber backing grips the floor and stands up to wet conditions, so the mat works at an interior lobby or a covered outdoor entrance alike.

Where It Belongs, and What It Is Not

Super Berber fits heavy-traffic entrances where appearance counts as much as cleaning — office buildings, shops, lobbies, schools, airports, and sport concourses. It works indoors or at a covered outdoor entrance, and it sits in our range of moisture-control entrance matting as the absorbent option that traps water in the pile rather than channeling it away.

What it is not is a drainage grid or a heavy-mud scraper. It holds the moisture it collects, so where standing water has to drain off, an open grid mat is the better tool — and where shoes arrive caked in mud, a coarse scraper out front will spare the pile. Super Berber is the mat that finishes the job: wiping shoes clean and dry once the worst is knocked off.

Three Things to Check Before You Spec It

First, decide what the door mostly throws at it. If the entrance is about moisture and a clean, finished look, Super Berber is built for exactly that. If shoes arrive heavy with mud or grit, set a coarse scraper ahead of it so the berber handles the wiping rather than clogging with debris it was not meant to take alone.

Second, size it and pick the edge. It comes in standard mats up to four by fourteen feet, in rolls, or custom-cut to your dimensions — up to thirteen feet two inches wide and inlaid runs to a hundred feet. Borders can be heat-sealed, square-cut, or beveled, and custom shapes are on the table if the entrance calls for one.

Third, plan the logo and colors early. The logo is needle-punched into the pile from a palette of up to 40 colors, so it needs camera-ready artwork before a quote. One thing to know up front: this construction does not do exact PMS brand-color matching — you choose from the 40 — so check that your colors are covered before you commit.

Why Mats Inc.

We have specified entrance matting since 1964, and a logo mat only works if the artwork, the colors, and the size are right before it is made. We take your logo, match it to the available colors, confirm the size and border, and lay out the inlay — so the mat that arrives cleans the entrance and reads as your brand, not a near-miss. Send your artwork and we will start there.

Frequently Asked Questions

What is Super Berber Matting made of?

Answered by Dustin Thompson, Owner & CEO

It is built from 100% solution-dyed polypropylene berber, needle-punched into a dense half-inch pile of about 52 ounces per square yard, over an all-weather rubber backing. Solution-dyed means the color runs through each fiber instead of sitting on the surface, so it resists fading and bleaching. The polypropylene is UV- and abrasion-resistant, which is what lets the mat keep its look under heavy traffic, indoors or at a covered outdoor entrance.

How much traffic can it take, and how well does it handle water?

Answered by Dustin Thompson, Owner & CEO

It is rated for heavy traffic, and wiping is its strong suit — the deep berber pile is built to pull moisture and fine dirt off shoes and hold it down in the fiber, away from the floor. The solution-dyed, UV- and abrasion-resistant construction keeps it from looking worn or faded as the traffic adds up. Like any pile mat, it performs best when it is vacuumed regularly and washed when it needs it, so the trapped soil does not pack down into the pile.

Is it a scraper or a wiper, and where should I place it?

Answered by Dustin Thompson, Owner & CEO

It does both, but it leans wiper — it is at its best absorbing moisture and fine grit rather than knocking off heavy mud. Place it where it covers the full walking path so shoes take several steps on it. If the entrance sees heavy mud or sand, put a coarse scraper mat outside the door first and let Super Berber do the wiping inside; that two-stage setup keeps the pile from clogging and keeps the floor beyond it clean and dry.

Can you inlay our logo, and how sharp will it look?

Answered by Jinna Hopson, Vice President of Marketing

Yes — the logo is needle-punched right into the berber pile, not printed on top, so it wears in with the mat instead of scuffing off. It is one of the largest custom logo mats made, which gives a logo room to read cleanly at the door, and custom shapes are possible if you want the mat itself to follow a form. We do need camera-ready artwork before quoting, so the inlay is laid out accurately from the start.

What colors can we get, and can you match our exact brand color?

Answered by Jinna Hopson, Vice President of Marketing

There are up to 40 colors to build the base and the logo from, which covers most brand palettes. The one honest limit to flag: this construction does not offer exact PMS brand-color matching — you choose from the 40 standard colors rather than a custom-mixed shade. Because the colors are solution-dyed into the fiber, whatever you pick holds up without fading. Send your brand colors and we will confirm the closest matches before anything is made.

Will it still look professional after a season of heavy use?

Answered by Jinna Hopson, Vice President of Marketing

That is what the solution-dyed berber is for. With the color locked into the fiber and the polypropylene resisting UV and abrasion, the mat holds its appearance far better than a surface-printed mat, which tends to go pale and tired at a busy door. The berber texture reads clean and upscale rather than utilitarian, so it suits a lobby or storefront where the entrance is part of the first impression.

By Jinna Hopson, Vice President of Marketing, Mats Inc.